T-REX 150 devo 10仿Alan設定檔

andy289777

這是我參考Alan的影片(http://www.youtube.com/watch?v=A1Q0AiDkfXk) 後面的參數 移轉到devo 10的
分享給各位devo 10控玩家參考 , 請大家仔細評估後小心使用
有什麼需要改進的也希望跟我說^^

熄火開關RUD DR1
3D模式1 FMODE1
3D模式2 FMODE2

陀螺儀感度
MIX0/MIX1/MIX2
50/70/73                //這邊應該還有很大的改良空間 , 還在測試怎樣調整能使急拉時不甩尾

--------從下行開始--------
name=150-3D!
mixermode=Advanced
icon=HELI.BMP
[radio]
protocol=DSMX
num_channels=6
tx_power=100mW

[protocol_opts]
Telemetry=Off

[channel1]
safetysw=RUD DR1
safetyval=-100
max=100
min=-100
template=complex
[mixer]
src=THR
dest=Ch1
curvetype=5point
points=-100,-40,-20,0,10
[mixer]
src=THR
dest=Ch1
switch=FMODE1
curvetype=5point
points=80,72,68,72,80
[mixer]
src=THR
dest=Ch1
switch=FMODE2
curvetype=fixed

[channel2]
reverse=1
max=100
min=-100
template=simple
[mixer]
src=AIL
dest=Ch2
curvetype=expo
points=30,30

[channel3]
reverse=1
max=100
min=-100
template=simple
[mixer]
src=ELE
dest=Ch3
curvetype=expo
points=30,30

[channel4]
reverse=1
max=100
min=-100
template=simple
[mixer]
src=RUD
dest=Ch4
curvetype=expo
points=15,15

[channel5]
max=100
min=-100
template=complex
[mixer]
src=MIX0
dest=Ch5
switch=MIX0
scalar=50
curvetype=deadband
points=0,0
[mixer]
src=MIX1
dest=Ch5
switch=MIX1
scalar=70
usetrim=0
curvetype=deadband
points=0,0
[mixer]
src=MIX2
dest=Ch5
switch=MIX2
scalar=73
usetrim=0
curvetype=deadband
points=0,0

[channel6]
reverse=1
max=75
min=-75
template=complex
[mixer]
src=THR
dest=Ch6
usetrim=0
curvetype=5point
points=-30,-16,0,50,100
[mixer]
src=THR
dest=Ch6
switch=FMODE1
usetrim=0
curvetype=5point
points=-100,-50,0,50,100
[mixer]
src=THR
dest=Ch6
switch=FMODE2
usetrim=0
curvetype=5point
points=-100,-50,0,50,100

[trim1]
src=LEFT_V
pos=TRIMLV+
neg=TRIMLV-
[trim2]
src=RIGHT_V
pos=TRIMRV+
neg=TRIMRV-
[trim3]
src=LEFT_H
pos=TRIMLH+
neg=TRIMLH-
[trim4]
src=RIGHT_H
pos=TRIMRH+
neg=TRIMRH-
[timer1]
type=countdown
[datalog]
switch=None
rate=1 sec
[safety]
Auto=min
[gui-128x64]
V-trim=55,10,1
H-trim=1,59,3
V-trim=69,10,2
H-trim=78,59,4
Big-box=2,12,Ch1
Small-box=2,28,Timer1
Small-box=2,38,Timer2
Small-box=2,48,Timer3
Bargraph=79,30,Ch1
Bargraph=85,30,Ch2
Bargraph=91,30,Ch3
Bargraph=97,30,Ch4
Bargraph=103,30,Ch5
Bargraph=109,30,Ch6
Bargraph=115,30,Ch7
Bargraph=121,30,Ch8
Toggle=75,13,1,64,128,FMODE
Toggle=84,13,2,65,129,MIX
Toggle=93,13,0,5,0,ELE DR
Toggle=102,13,0,4,0,AIL DR
Toggle=111,13,0,8,0,GEAR
Toggle=120,13,0,3,0,RUD DR
Battery=102,1
TxPower=75,1
quickpage1=Channel monitor

劉玹言

幫您補影片~感謝分享喔!!

阿翰

感謝分享

FLY翔翔

讚讚 感謝分享

吳仁遠

感謝分享

eded

感謝分享

k760724k

感謝分享喔!

s875714

感謝分享

batista123

感謝分享

DAT

感謝大大的分享!

ponx2k

感謝分享

陳青宏

感謝分享

熊大

雖然看的不是很懂，還是感謝分享

DAT

熊大 發表於 2014-3-25 20:04
雖然看的不是很懂，還是感謝分享

這是給DEVO 10刷完非原廠韌體專用的模型參數!