Spektrum AR7100R如何設限速器?

a532194

請問各為大大知道Spektrum DX7如何設定Spektrum AR7100R 限速器嗎?謝謝!

[ 本帖最後由 a532194 於 2010-4-15 21:43 編輯 ]

Chan710

我是用Spektrum AR7100R上的GEAR頻道連接定速器, 再在發射器(JR 9XII)的TRAVEL ADJUSTMENT內, GEAR設定為+/- 90% (~17000RPM, 是OS55最大扭力輸出的轉數), 用發射器的GEAR Switch, 就可控制定速器的開關.

僅供參考.

XBOY

meDX7SE+AR9000+亞拓RCE-G600orAR7100R定速器=RevLimit

阿為

可以將GEAR頻道連接定速器, 陀螺感度線連接AUX2,再將遙控器通道指向設成GEAR-->RUD  AUX2-->AUX2  ,就可以用gyro sens設定定速,用ADJ aux2設定陀螺感度

XBOY

AR7100R Output voltage - Rudder, Aux 2, Throttle 2, Gear 2 = 5.2 volts

DX7
If using the DX7, the following is recommended.
In system setup mode program AUX2 to GYRO and GEAR to AUX2,
the RevLimit will be controlled and adjusted via the AUX2 switch,
and all the target rpm』s will be adjusted using the GEAR channel
travel adjust.
Note: The Gyro Gain channel will plug into the AUX2 channel and the
gyro screen will be used to adjust the gyro gain (see the DX7 manual
for more detail on gyro gain settings).

In the travel adjust screen two values can be selected that will
correspond with the desired rpm. Note that two different rpms can be
selected, or if one value is programmed to zero, the RevLimit will be
turned off when the AUX2 switch is in that position.
Important: When calibrating the system the AUX2 channel must
remain at 100% in both directions.

XBOY

To Verify the RPM Sensor is Functioning
With the system calibrated and turned on, rotate the engine over by
hand and note the SENS LED on the receiver. When the crankpin
passes the rpm sensor, the SENS LED will light red indicating the
rpm sensor is working properly.

XBOY

Important: When calibrating the system, the limiter percentages
must be adjusted to 100% normal and -100% in ST1.
During calibration the RevLimit stores the output limits of the Gear
channel. It』s necessary to adjust the Gear channel output to 100% in
both directions during calibration.
1. Adjust the throttle operation so that the servo travel is near 100%
in both directions at full throttle and at full idle. This may require
lengthening or shortening the servo horn.
2. Make sure that the Gear channel is traveling 100% in both
directions when the switch that controls the limiter is flipped (flight
mode on the X9303 2.4GHz or Aux 2 on the DX7). The servo
monitor is helpful here.
3. Set the throttle trim to the low (off) position.
4. With the throttle stick at low throttle, turn on the transmitter then
turn on the receiver; within three seconds toggle the switch that
will control the limiter. The ACT LED on the receiver will flash
green indicating that the calibration mode is successfully entered.
5. Raise and lower the throttle stick throughout its full range. The
throttle endpoint will be stored.
6. Exit the calibration mode by toggling the controlling switch twice.
The ACT LED will stop flashing, indicating a successful calibration
was achieved.
7. To verify correct calibration, lower the throttle stick below the 25%
position and the ACT LED should turn off. Above 25% the ACT
LED (green) should be on.
Note: Calibration only needs to be performed when first setting up
the RevLimit, or when changing throttle servo throws, or if the unit is
installed in another helicopter.

愚公

X盒子大 可不可以用中文 不要欺侮我這種看不懂豆牙菜的小勞工好不好

XBOY

OK

AR7100R輸出電壓 - 魯德爾，奧克斯 2，節氣門 2，齒輪 2 = 5.2伏特

DX7
如果使用DX7，下面的建議。
在系統設置模式程序AUX2為陀螺儀和齒輪到AUX2，
該 RevLimit將通過控制和調整 AUX2開關，
和所有的目標轉速的調整將是利用齒輪通道
旅行調整。
註：陀螺增益頻道將插入到AUX2通道和
陀螺儀屏幕將被用來調整陀螺增益（見 DX7手冊
為更詳細的陀螺增益設置）。

在旅行調整屏幕兩個值可以選擇將
符合所需的轉速。請注意，兩個不同的轉速可
選擇，或者如果一個值被編程為 0，將 RevLimit
關機時，AUX2開關在這一立場。
重要事項：當校準系統的AUX2通道必須
維持在100％的兩個方向。

XBOY

重要事項：當校準系統，限百分比
必須調整到100％-100％的正常和超級一號貨站。
在校準 RevLimit存儲輸出限制的齒輪
渠道。因此有必要調整齒輪通道輸出 100％
在兩個方向校準。
1。調整油門操作，使伺服旅行接近100％
在兩個方向上，並在全油門全速閒置。這可能需要
延長或縮短伺服號角。
2。請確保齒輪通道行駛 100％都
當方向控制開關限製器翻轉（航班
模式的X9303 2.4GHz或輔助 2對 DX7）。伺服
監測有助於在這裡。
3。油門微調設置到低（關閉）位置。
4。隨著油門桿低油門，然後打開變送器
打開接收器; 3秒內切換開關
將控制限。澳大利亞首都地區接收器的LED將閃爍
綠色，表明已成功進入校準模式。
5。提高和降低油門堅持在其全系列。該
油門端點將被保存。
6。退出校準模式切換控制開關兩次。
澳大利亞首都地區 LED將停止閃爍，顯示出成功的校正
達到了。
7。要驗證正確的校準，降低油門桿低於 25％
位置和ACT LED應關閉。 25％以上的ACT
LED（綠色）應。
註：校準只需要執行時，首先成立
在RevLimit，或當改變油門伺服拋出，或者如果該單位是
安裝在另一架直升機。

XBOY

為了驗證轉速傳感器運作
隨著系統的校準和打開，對發動機的旋轉
桑斯的手，注意接收器的LED。當連桿軸頸
傳遞轉速傳感器，桑斯的LED會亮起紅色指示
轉速傳感器工作正常。